Repairs · Royal Beach
Garage Door Perimeter Weatherstrip in Royal Beach
Every time the door closes there is a rubbing squeal along one side, and the flexible fin has folded under itself and torn.
In plain words
For an attached garage the perimeter seal does more than keep leaves out. The garage is a buffer between the weather and the house, and drafts around the door cool the wall it shares with the kitchen and the floor of the room above it. Snow blown in melts and refreezes on the slab, and mice follow the warm air in at open corners. A well-fitted side and header seal closes those paths and eases the job of the weatherstripped door between garage and house, though the garage's warmth also depends on the door's own seal, the ceiling and the heating. It is a worthwhile comfort improvement for the house.
How the visit goesDry leaves keep appearing in the same corner inside the garage, and this fall there were mouse droppings along the wall beside the door. When you look, the corner where the top and side strips meet is wide open.
Garage Door Perimeter Weatherstrip
How the visit goes
What has been getting in, and what the garage is for
A short conversation shapes the rest of the visit. Is the garage attached and heated, or a detached shell? Has snow, water, leaves or an animal been coming in, and where? Is the door used several times a day or once a week? Was the door itself replaced or adjusted recently? A heated garage under a bedroom justifies a full one-piece stop and careful corners; a detached garage used for storage may want a straightforward fin replacement. Knowing what the household has noticed also tells the technician which side to test first and whether a section of jamb has been wet for a long time.
Replacing the wood stop with a one-piece vinyl stop
When the old wood stop is cracked, rotten or buried in paint, it is replaced rather than covered. The one-piece stop, a rigid vinyl moulding with the flexible fin formed along one edge, is cut on a mitre saw to header and side lengths and fitted the same way, header first. It needs no paint, does not rot, and its fin and stop are one part, so the seal cannot peel away from the moulding. Corners are either mitred or the sides butted tight under the header with the fins overlapped. The result looks like fresh trim and works as a seal.
Slush, salt and the bottom of the jambs
The lowest part of each jamb is where the weather does its work, so a little attention there protects the whole seal. Push slush away from the jambs when clearing the driveway rather than piling it against them, and rinse the salt off the bottom of the stop on a mild day. Keep the joint between the jamb and the sill caulked so meltwater runs off the face instead of behind it. If a section of jamb was replaced, keep its paint or PVC surface intact. A dry jamb base holds its fasteners, and fasteners that hold keep the seal tight.
Garage Door Perimeter Weatherstrip
In the van
Flat bar, hammer and nail set
Exterior caulking and gun
Galvanized or stainless trim nails
Epoxy consolidant and exterior primer
Aluminum retainer and rubber insert
Garage Door Perimeter Weatherstrip
What affects the quote
Jamb material
Wood jambs take nails; steel or aluminum-clad jambs need screws and sometimes a backing piece, and masonry openings need a different fixing altogether, each with its own time and hardware.
Size of the door
A double door has a longer header and the same two sides as a single, so more material and a two-person lift for the top piece; taller openings take longer side lengths.
Colour and profile
Standard colours and fin widths are carried on the truck. A less common colour, an extra-wide fin or a commercial retainer with insert may be a special order, with the difference noted.
What to have ready
- Have mice, leaves or water been getting in?
- Is the existing seal a flexible strip on a wood stop, or a one-piece vinyl moulding?
- Is it a single or double door, and roughly how wide and tall?
Garage Door Perimeter Weatherstrip: questions
QuestionsMy door was replaced last year. Does the perimeter seal need doing too?
Often, yes. A new door is sometimes fitted against the original wood stop and its old fin, and the new door may sit slightly differently in the opening, so the old seal no longer meets it. If daylight shows at the edges or the fin is hard and cracked, a new seal set against the new door completes the installation and matches the fresh look of the door.
Why should the seal only touch the door lightly?
The fin is meant to bend against the door with a small, even deflection. That is enough to seal, and it lets the fin spring clear as the door lifts. Pressed hard, it drags on the door face, folds under on the way down, squeals and wears through well before its time, and it adds load to the opener. Set too far off, it leaves a standing gap. The light touch is the setting that lasts.
What should I do before the technician arrives?
Move the car out of the garage or well back from the door, and clear anything stored against the jambs inside and any bins, planters or snow piled against them outside. Leave the door closed so the gaps can be seen as they are. If you have noticed where the daylight, drafts or snow come in, or where the mice appear, be ready to point it out.
Related services
- Garage Door Tune-UpSince the first cold snap the door has been sluggish.
- Off-Track Garage Door ResetYou tapped the door with the bumper while backing in, barely a nudge, and now the bottom corner has swung inward.
- Garage Door Panel ReplacementYou misjudged the last metre of the driveway and felt the bumper meet the door.